DIY Treatment Stops Engine Tapping. 

Fastengine fix.com car owners are amazed this DIY Mega Power Additive Engine Treatment stops their horrible engine tapping problem.Vehicle owners of Fastengine fix.com are amazed at how quickly this DIY Mega Power Additive Engine Treatment stops their horrible engine tapping problem. Your best solution for engine problems.


DIY treatment stops engine tapping

Car owners find it very expensive to fix their engine valve tapping problem. Tearing  it apart  to get to troublesome tapping valves and lifters runs $4000 or more.

However, many vehicle owners look to addives like the Maga Power Brand Engine Treatment to stop tapping. A sound like the engine is rattling lose is quieted by closing gaps. Done by cleaning and freeing, opening block oil delivery ways, and reconditioning to close the spaces - the problem, and tapping parts revert to their quiet operation.

Cost  is way less than its repair and can be installed into the fuel and motor oil easily in ten minutes. About $400 for large engines with 3 to 10 gallon oil capacity engines. Smaller sizes for  about $100 for a car/pickup engine. 

Mega Power Directions.

There are 2 simple Add and Drive Steps

  1. Step One uses 3 items. Add 3 items as shown to the gas and oil and drive as usual begins quieting the tap.
  2. Step Two ends the tap and takes place a week later when  the tap problem is flushed loose and drained out. 2 other items are installed with the fresh oil to end the tap. That's the fix our way!
  • Order from these specials below

Ordering for DIY treatment stops engine tapping car and pickup size vehicles 

  • The Slo-Wear Mega Power Valve Noise Treatment includes 6 items shown and needed. With easy-to-follow directions. Phone help if needed- a free $50 value. Satisfaction Guarantee. Includes Fuel Injector cleaner, Combustion Cleaner tapping removing cleaners to remove carbon to start removing those tapping causes.  Then a week later Flush Out dirty engine tapping causes. With fresh oil add the stop tap and enhance oiling items to close all gaps causing the tap. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. Click cart button for payment.

Order 2 Treatments Clean and protect both your car lifters valves  motors and save $50. 12 items. $125+ $15 s&h = $140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end without notice.

Order 6 Mega Power Treatments to service 6 motors. Fleet epair shop servicing. Mechanics resale value $200 to $400 per service  price. 36 items. $300+ $20 s&h = $320 total. Not $450. Order now! Save $130 off your price. 

Order 2 Treatments Clean and protect both your car lifters valves  motors and save $50. 12 items. $125+ $15 s&h = $140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end without notice.


Cost  is way less and can be installed into the fuel and motor oil easily. About $400 for large engines, and about $100 for a car/pickup engine. 



to stop their engine tapping. It avoids a costly engine repair while giving the engine an extra power boost—a more accessible, way less expensive way to end your valve tap.

Stopping engine tapping this way offers a big engine power boost and de-smogging features as its tap quieting feature concludes.

While circulating in the engine, the treatment cleaning therapy stops the engine tapping  caused by engine-stuck valves or lifters.

Car owners using Maga Powers engine tapping treatment is a more accessible and less expensive way to solve the engine's valve tap problem.

Stopping engine tapping using this treatment offers the car owner an inexpensive solution. 

The treatment's powerful cleaning therapy effectively performs the engine's 25,000-mile service by cleaning the engine fuel injectors, combustion carbon, and smog-lowering areas. While stopping the engine tapping problem by clearing clogged oil passageways and super-lubing to end the engine's tapping cause, car owners have a fantastic solution to tapping and other engine problems from Mega Power additives.

Enjoy Mega Powers' science and chemistry to stop your engine tapping and gain its bonus racy-like engine performance result, better fuel economy, and less pollution as it contains your engine tapping. You can find more details about the product and order it below.

Enjoy Mega Powers science and chemistry, and stop your engine tapping—order below details. 

Car owners find this Mega Power Brand DIY Engine  Treatment stops engine tapping. While returning power and quietness to the engine, you get a $500 Dealership service for free! Avoids a costly engine repair. It helps your cars run longer and better. The sooner you order it, the sooner it starts paying you to use it.


Ending valve lifter noise tapping.This introduces a product to End Undesirable Motor Tapping Noises 

Mega Power Engine Treatment is added to the gas and motor oil and a simple oil change produces a healing feature. If The causes of tapping identified. Idea is to add what removes sludge but frees itself of the sludge for reuse.A valve lifter noise ending product Review.For avoiding an expensive repair as the fix. 

Valve lifter noise Contact Info: On a smartphone, To ask a question, order products listed, call us...at 512 665 3388 ...george 

Join those who know the dirty little secret that stops engine valve tapping. 

If your hunting for a good way to stop engine tapping noise. Here's the best remedy around - no kidding! This is, End Valve Lifter Tap 101. 

What are engine valve lifters? How does Mega Power, shown above, stop engine tapping noise problems? A DIY lo-cost alternative to repair for under $100.

What are engine valve lifters? 

The Old Way To End Your Motor tapping Problem:

Traditionally, the motor is dismantled to get to the engine parts parts tapping. Cost of labor and parts run $2000 to $5000. It takes from 2 days to a week. Each engine part is hand cleaned and re-oil and put back along with new parts causing the tapping.  

 Mega Power Engine Treatment to the rescue. Mega Power Research developed a engine treatment anyone can easily install in their motor that stops the horriblr engine tapping.  It replaces the expensive hand cleaning traditionally done and so expensive with a unique cleaning process, performed as you drive - which lets the cheistry circulate by engine forces to free and clean stopping the problem in as litlle as The product has been used by car buffs for 40 years as their secret to  gaining double the life from their diesels. The products has a number of items installed a week a part. Taapping stops while driving in as little as 10 minutes to an hour.  And every engine part gets a special cleaning not just the affected parts. Mechanics doing the tratment will charge up to $400 and more on expensive cars an trucks.. The product can be shipped to you to install for under $200. Comes with phone instll walkthrur and has a satifaction guarantee, incase the problem can't be fixed this way.

- the tapping parts out of wack.

After understanding the complex cause of valve lifter noise, Mega Power field tested a number of ingredients they invented that reverses the cause of this dirty condition, removes the dirty condition to get oil flowing to end the valve lifter noise problem.

expense, is still the way most mechanics do the fix. Its like going in for heart surgery when alternatives in the form of medicine work just as well. 

  • Repair requires a week in the repair shop while dis-assembly and cleaning occurs, lots of hand cleaning, some machining work, then new lifters installed, and reassembly as the fix. Its a good method! However.. Profiteers sell additives for this.
  • Part store additives are sold to end valve lifter noise - but has negative press from engine damage they cause. Stay away from those products. Science and chemistry's remedy...
  • Mega Power is a Valve Lifter Noise Treatment that cleans, frees  oil flow again, and with special lube conditioners  moves the adjuster outward, closing the gap, ends the tapping problem. Is that what you want to happen?
  • 2 easy to follow steps make it possible, and there is nothing to dismantle. Just add the products as shown. Driving does the fix. Sometimes instantly. Other times in a few days.
  • Some repair shops install the Mega Power Treatment for about $250 to $400, but most oppose its usage. However...
  •  Install it yourself for under $100. Does this method interest you and deserve a try?
  • The valve lifter noise ending treatment is delivered to your door in about 3 days with easy-to-follow directions, phone help, a guarantee. Men and women vehicle owners find it easy to end valve lifter problems and tapping this way.

Mega Power Directions.

There are 2 simple steps:

  1. Step One uses 3 items. Add 3 items as shown to the gas and oil and drive as usual. 
  2. Step Two takes place a week later when 3 other items are installed at an oil change. One just before the oil change. And 2 added on top of the new oil. That's the fix our way!
  • Order Now!  This also includes our specials here.

Ordering info.

  • Order one Mega Power Valve Noise Treatment. Includes 6 items shown. With easy-to-follow directions. Phone help if needed- a free $50 value. Satisfaction Guarantee. Includes fuel system  and combustion cleaners, and Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. Click cart button for payment.

Order 2 Treatments Clean and protect both your car lifters valves  motors and save $50. 12 items. $125+ $15 s&h = $140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end without notice.

What you should know about valve lifter noise.

  • Other than repair, this is the only known way to correct problem by Mega Power's additive treatment. 
  • Powerful treatment cleaners in Mega Power will remove oil blockage, and residues to free and expand the lifters.
  • With a cushioning quieting feature - it allows oil to again flow, closing the lifter space to end the tapping noise.  
  • That's way cheaper than by repair!

I've removed and reconditioned valve lifters for myself and customers when they tap - but I found a product that does it for me, makes me loyal customers, by being the best remedy for car owners with the tap problem. Avoids a big repair bill, too! Shown in the picture above.

You may seek advice from your mechanic about your noise. It's not good news either. And most of them refuse to use additives. We like to sale big repair jobs - that's why! Not me!

Google may have led you here as you searched for a less expensive way to get your car running quiet and great again. This is it!

Introducing the product in the picture from Mega Power. A new additive way that ends lifter and valve tapping - as you drive.

How to  install Mega Power Valve Lifter Noise Treatment to end tap tap tapping, like I do!

Please note:

  • Because your engine problem is complex, so is the Mega Power Product. It has to be to quiet your tap. However...
  • The install of Mega Power is easy! The results are very fast!
  • Men and women easily perform the simple install, and results quiet their motor's tapping noise - in as little as ten minutes!
  • Nothing to take apart! And more good news is its a 10th of the cost compared to actual repair.
  • Your motor will quickly return to a strong running, quieter-than-ever operation - How so explained below.
  • The install procedure is simple.  6 items are needed. You add 3 to the gas and oil to start the fix, then add the other 3 during an oil change a week later. That's the permanent fix I and many now use.

More on Directions Procedure - You can do it yourself!

There are 2 simple steps:

  1. Step One: Add 3 items as shown to the gas and oil and drive as usual. I add numbers to each items to follow the 2 steps.
  2. Step Two takes place a week later. Add 3 other items at an oil change. One just before the oil change. And 2 added on top of the new oil. That quiets the noise!

How Mega Power protects all your cars and saves you money.

  • If it fails to work and repair is actually needed - send us the paid invoice for a quick refund. Please note: 2 refunds last 267 days. Many thousands of satisfied customers. Order Now to avoid more costly damage!
  • The install of the 6 items needed is easy and results happen in a bit of driving. Order one of these specials - here.
  • This same product protects good motors  - from such problems. Its still in use as a fluid exchange service for your newer cars 25,000, 50,000, !00,000 miles warranty service requirements. It exceeds every car makers specs, diesel and gas.  
  • What it does: It is a re-conditioner that changes dirty, wear roughen and trouble causing piston bearings valves and gears back to clean smooth trouble free operating ones.
  • Selected to extend the life of older, worn motors - and transmissions - returning a like-new performance that can be extended for many years - with touch ups during future oil changes.
  • See ordering info and specials - below.

Ordering info. Order now! 

Mega Power Valve Treatment is shipped to your door in a few days with directions and phone help if needed. If you want a quiet motor. Want to avoid an expensive repair bill, try this product that has many happy users. Only 2 refunds ask for last 267 day.

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. With easy-to-follow directions. Phone help if needed- a free $100 value. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h = $95 total. 

Order 2 Treatments to clean an protect both your car motors and save $40. 12 items. $125+ $15s&h;=$140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end without notice.

Order 6 Mega Power Treatments to service 6 motors. Fleet or mechanics resale value. 36 items. $300+ $20 s&h = $320 total. Not $450. Order now! Save $130 off your price. 

Whole vehicle protector special.

Order the Engine$95 and Transmission Treatment$75 and our Bonus $39 Power Steering System Protector Now Free. And Bonus Radiator System Protector $39 also Free. Total 11 items regular $248. Just $150 + $15 s&h = $165. Save $83 per set. Order one or more sets for just $165 each set. Save $83.   

What you should know...Know the following and protect your cars and your cash reserve.

Trouble starts long before the tap appears.

It starts as extremely hot combustion "blows-and by" escapes as you operate your motor, by slipping pass the pistons - see downward arrows.

Blowby sludge's the oil.

When minute amounts of residue blocks oil to the lifters, the lifter piston drops and a space appears. 

With each rotation of the engine, the lifter closes the newly-appeared space with a  hammer-like blow you hear as a tap tap tap. That tap is not good, of course.

Blowby, residues and sludge are trouble makers that Mega Power will remove - because oil can't! Our method is offered in the recommendations below.

What are ways to end their tapping?

Oil changes and part store additives have until now, not been able to correct the problem until Mega Power valve treatment  was invented. It works because it cleans and frees the lifter and this restores quiet operation again.

Mega Power works well in transmissions, radiators and steering systems to end their wear and residue caused problems.

Mega Power is installed prior, and during fluid replacements detailed below.

What Mechanic's do.

Traditionally, us mechanics have had to dismantle your engine, get to and replace those many lifters, and do a rebuilding work on the engine to end the problem. Costs run from $1500 for small engines to $4,500 for v6 and v8 engines and diesel motors. 

With Mega Power, sludge is removed by penetrents, conditioners and cleaners, a friction remover, and co-polymer to fill worn spaces, that all go where oil and other products cannot, to dissolve the sludge. This is done in a 2 step fashion, and with driving involved. Nothing to take apart. Cost is $250 to $450 if a mechanic installs Mega Power, under $100 if you do it yourself. Mega Power is shown here.

Those are now the 2 ways to fix your cars dirty lifter problem.

It's true that mechanics charge $2000 or more to clean out and replace dirty, affected lifter and valve parts. Our way is cheaper! About $250 if a mechanic sells you the service. Under $100 now while on special if you install it. It's easy, and I'm here to help you.

Order now! Mega Power Valve Treatment is shipped to your door in a few days with directions and phone help if needed. If you want a quiet motor, avoid an expensive repair bill, try this product with many happy users. Only 2 refunds asked for last 267 days.

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if needed- a free $100 value. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. 

Order 2 Treatments to clean and protect both your car motors and save $40. 12 items. $125+ $15 s&h = $140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end without notice.

Please note: This review of the above products explains the best, and cheapest way to restore your motor's strong quiet valve lifter performance again.

Our Review.

The 8 to 24 engine parts known as valves in your engine, and their lifters perform the breathing function in your motor, and cause your problem.  The noise they produce appears your when motor oil can no longer remove varnish and sticky residues on those items. 

Before I show you how to install this Mega Power Product to end your motor's valve lifter noise, a little education about why it happens, and how Mega Power works to end the tap cause will also teach you how to avoid most other engine transmission radiator and steering problems, too.

Knowing that info for valve care includes advantages to avoid other motor problems, now in the making, [and avoids transmission problems if you add this product to its fluid]. This review will show you how to keep your engine and transmission of all your cars trouble-free and your budget healthier!

  • The Mega Power Brand method of Car Care has saved me and the many thousands of other car and equipment owners tens of thousands of dollars by its advantages to remove internal acid, wear, friction and their performance declining problems that cause your present engine problem.
  • As a mechanic, and many mechanics who understand  - not just how to replace bad parts, but have taken the Mega Power Training about How to fix your valve lifter noise mechanical problem chemically, is what also restore's a  tuned, serviced, or repaired car's great like-brand-new performance, and keeps it that way indefinitely.
  • That's this same Mega Power Method I want you to use to end your tap problem!
  • As a mechanic, Mega Power Treatment is the inside secret I use to make the cars I fix, tune, and service, run like they instantly have a bigger engine - yet get 20 to 40 more miles on fill ups each week like a smaller motor gets. 
  • You want and need those Mega Power's tap ending, valve lifter noise fix advantages, also! No other product has those advantage!

Directions to stop valve lifter noise.

Mega Power uses 2 steps: Step One use 3 items in the gas and oil to clean ,remove, and stop dirty combustion conditions that slip down into your motor oil to jam lifters and stick valves.

Step Two uses 3 item a week later to finish the cleaning wherever oil goes cleaning the piston rings, valves, and lifters, ending the valve lifter tap permanently!

Mega Power's protective anti-wear coating - a $100 value by itself, but included as MC+ then keeps every top and bottom valve and lifter part clean and long wearing - resulting in a like-new quieter operation. Your motor needs this treatment to stop its valve lifter noise!

It's true that mechanics charge $2000 or more to clean out and replace dirty, affected lifter and valve parts. Our way is cheaper! About $250 if a mechanic sells you the service. Under $100 now while on special if you install it. It's easy, and I'm here to help you.

Order now! Mega Power Valve Treatment  is shipped to your door in a few days with directions and phone help if needed. 

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if needed- a free $100 value. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. 

Order 2 Treatments to clean an protect both your car motors and save $40. 12 items. $125+ $15s&h;=$140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end without notice.

Order 6 Mega Power Treatments to service 6 motors. Fleet or mechanics resale value. 36 items. $300+ $20s&h;=$320 total. Not $450. Order now! Save $130. 

While I use this web site to train mechanics in this expertise, to increase their customer-pleasing, profit-improving capabilities, I show its easy install so you or any non-mechanical man or women can get the same professional results.

So read along and let me introduce the easiest, and  product known to end your valve lifter noise.

Valve lifter tapping:

It occurs when several internal negatives jam the valve lifters, or slows down the closing of your engine valves a space appear, and with each engine rotation the engine smacks close the gap and your tap or knock repeats itself!

Now there's two ways to end and the second way is a DIY Treatment stops valve tapping.

This  covers the Mega Power Treatmentto stop your troublesome, stuck valve lifter noise tapping. 

Valve Lifters are thumb size mechanical devices in all engines - one for each of your motor's  8 to 24 valves having 2 functions:

  1. Lifters, or adjusters as I call them, one lifter for each of your motor's fuel and exhaust valves, push them open and close - with a cam assistance, to let fuel in, and exhaust out of your motor - a dozen times a minute as you drive down the road. See picture above. That's the first job of a lifter.
  2. Because engine valves take the motor's worst punishment under 1800 degree temperatures, even though heavily oiled to cool and lube them, valves wear out the fastest- causing a drop of power and noisy operation - both are worrisome and costly negatives to correct - and avoid, if possible. 
  3. To overcome the wear factor, engineers designed lifters to have a pencil-eraser size little piston that expands under oils pump pressure to take up wear space as valves wear - to keep power up, and engines quiet operating.  The second job of a lifter. 

Since a lifter or its valve  is  now causing your engine problem, I'll end that worry for you! My tips, and product suggestion will return "their quiet operation" into a surprisingly better running car. This also avoids an expensive repair. That's why you're here! To do so...

What You should know...

Because many kinds of valves operate to make engines and transmissions and other components work, valves and lifters become troublesome when dirty, worn, and this deters running and shifting and cooling performance negatives you are experiencing.

Dirty moving parts is what cause "millions of premature engine and transmission repairs" last year. So says a National Transmission Association Forecast Builtin - about what to expect in the near future also.

If you think about it, when your car or equipment was new, lifters and other parts were clean, fit together, are easily movable, ran dependably, and help produce the most zip, power, and best fuel economy - you bought the car for.  However....

You can blame valve lifter noise, and its tapping sound - and years-shorter engine life, and shorter transmission life - for that matter, on acidic residues that the motor makes.

Just a thin sticky acidic film - which eats away those surfaces, increases friction drag,  faster wear increasing problems, and a foothold for residues  - without your knowledge - as you start the motor and take off, and drive  here and there everyday - until residues and or friction causes the valve lifter noise - or another car and worry producing negative in your life. 

Many troublemakers. A Mega Power Complete Solution.

I'll show you how to end both problems.

Sure, you use good oil - but sludge and residues form anyway, create sudden valve lifter noise, and wear out your motor and its power years faster. How so?

This results from combustion - about 1800 degrees, and acidic compounds which slip pass the piston, and mix with oil. There, they create residues. What diesel and gas and motor oil filters don't get, coat every piston and gear part.

As more heat, acids, and combustion create more varnish and residues some residues travel to and block the valve lifters of oil at the end of the oil supply route.

Valve lifter noise appears.

The tap problem happens when lack of oil from blockage causes the adjuster to drop - like a tire with a hole in it, and a space appears.

As the space closes on each rotation a hammer-like smack occurs.  That is the cause of valve lifter noise and tap tap tap. Good oils can't prevent this problem - though the ads say so!

What us mechanics are trained to do to end valve lifter noise.

We take your engine apart, clean every part, machine others, and replaces all the lifters - for a $3000 plus cost.

How Mega Power Engine Valve Treatment Stops valve lifter noise for good!

Mega Power follows a 2 step treatment where acids are neutralized as you add the products to the gas and oil, and a cleaning, freeing operation works as you drive. This returns the motor to its original quiet operation. Imagine that pleasing development!

While some part store additives are are sold for valves and cleaning, most are thick honey-like and only muffle the sound, and others use solvents to flush the motor - now proving damaging.

Mega Power's method provides a new Hi-tech way to solve the valve lifter noise problem. Doing so with crawling cleaners - 6 of them! That chemically penetrate where oil cannot go to clean and free the lifter. This action opens the passage way - again letting oil pump up the little adjuster in the lifter - closing the gap, returning quiet to the engine again!

Besides that, Mega Power 6 ingredients provide other beneficial anti-wear, conditioners, and friction modifiers your motor needs. Their bathing of every part cleans them, frees and coats them, adding a slippery protective film on every part.

That Mega Power Product and its Treatment Advantage is what has been found to return the original near new quiet strong operation.

That's what you are after, isn't it?

With oil free and flowing again the lifter adjuster rises closing the gap - ending the tap as you drive. Mega Power does so at a fraction of the cost of actual repair. Results are permanent. 

Thousands of car owners have opted for the Mega Power 6 item cleaner below as Mega Power cleans  the passage ways and lifters of residues. These 6 items have been found to remove the tap causing residue formation that makes valves and their lifters stick.

Directions to stop valve lifter noise.

Mega Power uses 2 steps: Step One use 3 items in the gas and oil to clean and remove dirty conditions that slip down into your motor.

Step Two uses 3 item a week later to finish the cleaning wherever oil goes cleaning the piston rings, valves, and lifters, ending the valve lifter tap.

The protective anti-wear keeps every part clean and slows wear - resulting in a like-new quieter in operation. Your motor needs this treatment to stop its valve lifter noise!

It's true that mechanics charge $2000 or more to clean out and replace dirty, affected lifter and valve parts. Our way is cheaper!

Order now! Mega Power Valve Treatment  is shipped to your door in a few days with directions and phone help if needed. 

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if wanted. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. 

As a mechanic, taking motors and transmissions apart, you see 3 things happen that cause the valve lifter noise  - and rough shift problem.

  1. This internal spreading around of residues which then gum up the pistons valves and their lifters. And shift valves. Cause tapping.
  2. Acids etch your piston bearing and gear surfaces creating friction.
  3. Friction and binding= more friction to wear out your car years faster. That makes engines and transmissions seem worn out, but eye balling them only show roughness and residues. 

Mega Power Engine and Transmission Treatment clean. heal, smooth and fill worn spaces. This makes a complex problem solver like no other!

Mega Powers other advantages all your cars and equipment need

  • The motor's PCV system - a device added by law to all engines to curb smog, sends some of the vaporous acids, moisture and un-burnt fuel from the motor oil area, back up into the fuel, air entree  stream for re-burning.
  • That's not good for the top of the motor, nor the bottom parts.
  • As Mega Power cleans by vapor action the PVC system - as well as wherever fuel air combustion blowby oil and exhaust go a breathing and cleaner combustion and more horsepower out put results.

As your motor's mixture of heat, moisture, and sulfurs spreads into the motors oil, oil breakdown [sludge] forms. Sludge circulates into valve lifters, causing oil blockage - lifters are hydraulic adjusters that use motor oil to take up wear spaces. 

When residue blockage occurs, lifters - you have one for each of your 8 to 24 valves] collapse. A space then appears between the lifter and valve.

As this occurs lifter rotation smacks the valve, making a hammer blow tap sound. Usually an engine overhaul needing remedy. However...

A new product from Mega Power removes sludge and frees the  lifter, which closes the space and ends the valve lifter noise.

New types of cleaners, conditioners an acid neutralizers, along with co-polymers - covered below, from Mega Power will correct those conditions and mechanic can learn the install process from this article.

Blowby fumes - always full of acids, results from extremely hot combustion slipping pass the pistons rings - where those fumes enter the motor oil area. Bigger engines have more blowby. However, with time, residues slow the piston rings ability to flex and block blowby, and more blowby escapes - and full horsepower development lowers a bit.

Acids pit and remove surface rubbing material - creating faster wear and friction. A second form of  power loss. Oil break-down forms [a sludge], circulating in a gravy-like goo.

That tar-like goo is what coats your valves making them slow closing, and blocks oil flow needed to keep your valves hydraulic lifters [adjusters] tight and quiet operating.

When sludge blocks oil flow to the lifters, lifters collapse, a space develops, and the tap tap tap sound appears. Get it? Complicated - right?

Well, the point being, sludge is caused by blow-by  and is the 3rd causes of valve tap - and Mega Power ends all 3 dirty problems for you, you thought your good oil was suppose to do - but, can't!

How Mega Power Stops valve lifter noise for good!


I read of ending your motor valve lifter noise in 3 ways. Some good, some harmful. For example...

  1. Solvent engine flush additives, called engine flushes, are often considered as a remedy to end lifter tap. However, they cause engine failure problems. Stay away from those products.
  2. The mechanic's repair way. The common method is take apart your engine and have it basically rebuilt. A mechanic dismantles the top half of your motor. Noise causing dirty valve parts are removed, required machining performed to clean-them-up. Deeper in the motor your motor's many hydraulic lifters are yank out like a dentist pulling teeth, and new lifters installed, and your motor reassembled, as the fix. Cost $3500.
  3. The other way  I like to stop valve lifter noise - and I promote that's cheaper is to install a new product called Mega Power - shown below.  Mega Power avoids valve damage in several ways. One way is that it enhances lubrication and oil delivery with its cleaning ingredients. This powerful feature stops valve lifter tap by having the ability to go where oils and other additives cannot.  The freeing of stuck valve lifters expands them and closes a gap. This ends the noise and tapping. Is that what you're after?
  4. Come back and Read Dougs experience.  

Thousands of car owners have opted for the Mega Power 6 item cleaner  above as this cleans all 6 areas causing the residue formation that makes valves and their lifters stick.

Directions and the install are easy and driving stops the valve lifter noise.

Mega Power uses 2 steps: Step One use 3 items in the gas and oil to clean the top part of your motor.

Step Two uses 3 item a week later to finish the cleaning and add protective anti-wear to keep every part clean and slower wear - and like-new quieter in operation. Your motor needs this to stop valve lifter noise!

Order now and I'll ship this Mega Power Valve Treatment to your door. In a few days your motor will return to its best and quietest operation -at a fraction of what actual repair cost. Comes with a 12 month guarantee, too!

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if wanted. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. 

How valve lifter noise or tap starts.

You can blame valve lifter noise, and its tapping sound - and years-shorter engine life, and transmission life -for that matter, on combustion temperatures - about 1800 degrees, and acids that form from components in diesel and gas and motor oils.

With heat and combustion escaping down pass your pistons into your oil, - acids, residue sand friction form to cause tapping. As a mechanic, taking motors apart, you see 3 things happen Mega Power does to end valve lifter noise.

  1. Acids create sticky residues on valves and lifters causing the tap. Mega Power neutralizes acids ending their tap and wear making ways.
  2. Acids etch away the shinny smooth part surfaces causing more drag, faster engine transmission wear out. And binding troubles on valves and lifters. Mega Power heals and smooths those surfaces ending the tap, restoring power, and quieting thier noisy ways.
  3. Cleaners and MC+ clean and free lifters and valves from 2 sides to return a smooth, more powerful and quiet operating engine again for you!  Works in minutes and immediate results return.

Your engines internal creating residues are what gum up the pistons, valves and their lifters mega Power removes.

Acids come from combustion's escape - called Blowby, which sends heat, moisture, and sulfurs pass the piston into the oils - [as refining may not have refined enough or all the sulfur out of fuel and motors oils].

This PCV system - sucks up some of the vaporous acids, moisture and un-burnt fuel from the motor oil area, back up into the fuel, air entree system for re-burning. That's not good for the top of the motor,  and Mega Power cleans, then stops that harmful state. Complex - right? But needed!

As this mixture of heat, moisture, and sulfurs spreads into the motors oil, oil breakdown [sludge] forms. Sludge circulates into valve lifters, causing oil blockage - lifters are hydraulic adjusters that use motor oil to take up wear spaces. 

When residue blockage occurs, lifters - you have one for each of your 8 to 24 valves] collapse. A space then appears between the lifter and valve.

As this occurs, cam action smacks the lifter against the valve, making a hammer blow tap sound. Usually needing an engine overhaul remedy. However...

A new product from Mega Power removes sludge allowing the additive to free, and raises the lifter adjuster, which closes the space and ends the valve lifter tap noise.

This is possible with new types of cleaners, conditioners and acid neutralizers, along with co-polymers - the workable formula covered above, from Mega Power, will correct those conditions and can learn the install process from this article. 

Blowby fumes - always full of acids, results from extremely hot combustion slipping pass the pistons rings - where those fumes enter the motor oil area. Bigger engines have more blowby. However, with time, residues slow the piston rings ability to flex and block blowby, and more blowby escapes - and full horsepower development lowers a bit.

Acids pit and remove surface rubbing material - creating faster wear and friction. A second form of  power loss. Oil break-down forms [a sludge], circulating in a gravy-like goo.

That tar-like goo is what coats your valves making them slow closing, and blocks oil flow needed to keep your valves hydraulic lifters [adjusters] tight and quiet operating.

When sludge blocks oil flow to the lifters, lifters collapse, a space develops, and the tap tap tap sound appears. Get it? Complicated - right?

Well, the point being, sludge is caused by blow-by  and is the 3rd cause of valve tap - and Mega Power ends all 3 dirty problems for you, you thought your good oil was supposed to do - but, can't!

How Mega Power Stops valve lifter noise for good!

You may have many questions about your engine tap.

This review compares traditional repair to end this dirty engine problem, with new products from Mega Power. Mega Power's method chemically penetrates where oil can go to cleans to free the lifter - ending the tap as you drive. Mega Power does so at a fraction of the cost of actual repair. Results are permanent. Mega Power stops engine valve lifter noise for a smoother quiet running motor - at 1/10th the cost of repair. 

The two ways of ending your motor valve lifter noise

  1. The mechanic's repair method. The common method is to pay a mechanic to dismantle the top half of your motor. Dirty valve parts removed require machining to clean-them-up. Deeper in the motor your motor's many hydraulic lifters are yank out like a dentist pulling teeth, new lifters installed, and your motor reassembled, as the fix. Cost $3500.
  2. The other way is to install a new product called Mega Power - shown below. Mega Power works using a new breed of problem-solving chemistry that goes where even synthetic oil can't go. Its 6 ingredients of very powerful cleaners, conditioners, and valve lifter noise ending friction modifiers stops valve lifter tap fast. See Demo.

Anyone can easily install Mega Power Valve-Lifter-Noise Treatment. Shown here, Mega Power is easy to install by anyone - nothing to take a part. Works fast and works as your drive.

Guaranteed, if it doesn't end the noise, will prevent it from getting worst for 6 months to a year - to help you raise funds for its actual repair. Please note: 2 refunds last 267 days.  Is this the help you're after.

Directions: You add 3 items shown, the drive for one week. Add the other 3 a week later at an oil change. That is what works to end your valve lifter noise. Mega Power is sent to your door by FedEx in about 3 days with directions and phone help, if needed. Please note...

In transmissions, a similar valve - a shift valve causes rough, slow, or jerky shifting and Mega  Power ends that dirty valve hangup problem too - returning a smooth trouble free service to that component, helping car owners happily avoid another car fixing expense.

Mechanics that promote Mega Power charge Just $250 to install Mega Power. Just $100, if you install it yourself. It's easy, and takes no skill, and nothing to take apart. Any man or woman   will get professional results - Guaranteed! Those are your choices...

Mega Power will add years more quiet, dependable life to your motor at a much lower expense than repair, at $250 if a mechanic installs it for you. Under $100 if you install it yourself. If you  read this far, you need to order Mega Power. Order online or by phone. 

Ends valve lifter noise.

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if wanted. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h = $95 total. 
  • Order 2 Treatments to clean and protect both your car motors and save $40. 12 items. $125+ $15 s&h = $140 total. Not $190. Order for both cars to protect them, now, since you're thinking about it! Save $40.  Offer can end withou t notice.
  • Order 6 Mega Power Treatments to service 6 motors. Fleet or mechanics resale value. 36 items. $300+ $20 s&h = $320 total. Not $450. Order now! Save $130.

Before you qre shown the directions - considered below.

These three conditions cause your valve lifter noise 

  1. Acids from blowby sludge your oil. It then blocks oil to your valve adjusters and valves. This is not good, of course! Without oil pushing the adjusters outward, a space and the noise you hear occurs. Acids come from "blowby...
  2. Blowby means raw gas and hot acidic combustion blows from above your motors dirty, sluggish piston rings -This loss not only lowers horsepower, it also gums up critical parts - once clean an freely moving.  Blowby is  800 degrees hot an cooks your oil into tar. With acids and sticky residues  valve lifter noise  results.
  3. On valves, see picture, Sticky residues bog down valve closing speed. A space then appears and you hear your motor parts close the space with a hammer like tap.

You now know more about valves, and why valve lifter noise occurs and the reason for your car's tap than your mechanic! 

Do you want to just use his older, traditional method to fix the problem with a $3500+ engine overhaul?

What other option is there? 

The two ways of ending your motor valve lifter noise

  1. The mechanic's repair method. The common method is to pay a mechanic to dismantle the top half of your motor. Dirty valve parts removed require machining to clean-them-up. Deeper in the motor your motor's many hydraulic lifters are yank out like a dentist pulling teeth, new lifters installed, and your motor reassembled, as the fix. Cost $3500.
  2. The other way is to install a new product called Mega Power. Mega Power works using a new breed of problem solving chemistry that goes where even synthetic oil can't go. Its 6 item ingredients of very powerful cleaners, conditioners, an valve lifter noise ending friction modifiers. 
  3. Anyone can easily install Mega Power to end their motor tap an, if they want to avoid transmission trouble,  also clean their transmission shift valves twith Mega Power. Mega Power avoids  rough shifting - really! Just like Mega Power's valve treatment shown here, does. Mega Power is the other, smarter, cheaper, faster way to end your valve lifter noise. Cost: $250 if your mechanic installs it. $100, if you install it yourself. Guaranteed!

The Mega Power Valve Lifter Treatment installs easily to clean and free your stuck or sluggish valve or lifter  tap condition - and the cause  of the tap - sometimes in a few minutes, to a day of driving, customers tell us. That's my experience, too! And the best part - with this valve lifter tapping remedy, there is nothing to take apart! Driving does the fix!

Simple  to follow Directions: The valve treatment works in 2 steps like this.

Step One. You add 3 items for top of motor valve cleaning. One to the gas tank, to the oil, and vacuum for top of the motor valve cleaning. Drive as usual.

Step Two. A week later you add the 3 remaining items during an oil change. That takes away the cause of the problem and smooth, very powerful quiet smoothness - amazingly returns!

Pretty simple for a complex problem. These 6 items work together from 6 directions found to clean, condition and end the tap. Driving does the actual fix. Most times, the tap stops right away. Total cleaning of the 2 steps ends the problem permanently. 

Mega Power will add years more quiet, dependable life to your motor at a much lower expense than repair, at $250 if a mechanic installs it for you. Under $100 if you install it yourself. If you read this far, you need to order Mega Power. Order online or by phone.

Ends valve lifter  noise.

Ordering Info

  • Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if wanted. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $80, plus $15 s&h;= $95 total. 
  • Order 2 Treatments to clean and protect both your car motors and save $40. 12 items. $125+ $15s&h;=$140 total. Not $180. Order for both cars to protect them, now, since you're thinking about it! Save $40.
  • Order 6 Mega Power Treatments to service 6 motors. Fleet or mechanics resale value. 36 items. $300+ $20s&h;=$320 total. Not $450. Order now! Save $130.


You motor tap is caused by one of 3 negative conditions

  1. Your motor's dirty fuel intake valves, or exhaust valves - or valve adjusters - nicknamed lifters cause the noise. When so dirty, movement slows down their snappy up and down closing speed. Tapping results
  2. Or causes the adjuster to drop. Both problems creates a space and the tap as they bang against each other related part.
  3. So, if not dirty valves, its your motor's dirty valve lifters sticking such,  a space occurs, causing the tap.

Using Mega Power you clean and free all 3 areas of the tap ends your motor valve lifter noise and tapping.

Dirty rings, valves, and lifters indicate the dirtiness is about to cut your engine life in half! You don't want to go there, do you? No!

The tap is caused by another dirty condition called "blowby"

You can blame your tapping and years of shorter engine life from dirty, lazy piston rings. They allow boiling-hot 500 degree combustion gasses to slip past your motor's piston's, to mix-in with your motor's oil. Sound good to you? No, its not!

Oil break-down forms [a sludge], circulating in a gravy-like goo.

That tar-like goo is what coats your valves making them slow closing, and blocks oil flow needed to keep your valves hydraulic lifters [adjusters] tight and quiet operating.

When sludge blocks oil flow to the lifters, lifters collapse, a space develops, and the tap tap tap sound appears. Get it? Complicated - right?

Well, the point being, sludge is caused by blow-by  and is the 3rd causes of valve tap - and Mega Power ends all 3 dirty problems for you, you thought your good oil was suppose to do - but, can't!

How Mega Power Stops valve lifter noise for good!

The Mega Power Valve Treatment uses 6 items to get to, and remove what the best oils cannot - They cannot remove sticky residues on piston rings, motor valves, and valve lifter adjusters. The best oil cannot end  blow-by and your tap problem.

Mega Power has made it easy to correct this problem. Is that what your after? Order Mega Power below.

The install of Mega Power is simple, although Mega Power performs a complex, Hi-tech cleaning and freeing action, no synthetic oil can ever do. 3 Mega Power items shown go in the top gas, air and combustion side of the motor, and 3 into the motor's oil during an oil change, to end your tap work.

A remedy that ends the tap when nothing else can. No special skill needed, nothing to take apart. Just add as directed, and driving does the fix, quieting the tap - guaranteed!

Mega Power comes by FedEx to your door in about 3 days, with easy-to-follow directions, phone help if needed, and our guarantee. You can order the Mega Power Valve Treatment below.

Ordering Info

Order one Mega Power Valve Treatment. Includes 6 items shown. Easy-to-follow directions. Phone help if wanted. Satisfaction Guarantee. Shipped to your door by FedEx in 3 days. Just $75, plus $15 s&h;= $90 total.

Order 6 Mega Power Treatments to service 6 motors. Fleet or mechanics resale value. 36 items. $300+ $20s&h;=$320 total. Not $450. Order now! Save $130 more. 

Order 2 treatments and protect both car motors. Just $140 Save$40 on this spring time special.

Order 6 Mega Power Treatments to service 6 motors. Fleet or mechanics resale value. 36 items. $300+ $20s&h;=$320 total. Not $450. Order now! Save $130 more. 



What you should know: Treatment Advantages

This Mega Power Valve Treatment ends the valve lifter noise when nothing else can and ends several more wear, residue conditions that would soon cause other costly-to-repair problems - to boot!

That should be good news to you, if you're on a tight budget - and who isn't, these days?

Easy to use. Driving does the actual valve lifter noise fix

The easy-to-use Mega Power Product uses 6 special new ingredients for the fix.

Each ingredient penetrates a different problem area. See valve illustration and video, below.


There, they clean, free, heal, and smooth the affected valve - ending the problem - as you drive.

Customers who installed the Treatment - like Mike, tell us how Mega Power ended his valve-lifter-noise. Mega Power works as described. Order Mega Power Now. On a smartphone, To ask a question, order products listed, call me...George at 512 665 3388

Our privacy policy

Share this page: What’s this?FacebookTwitterPinterestTumblrReddit Whats App



Enjoy this page? Please pay it forward. Here's how...